Z4-400-42 400kw 440V 500rpm Motor Z4 Series DC Motor

Z4-400-42 400kw 440V 500rpm Motor Z4 Series DC Motor

Item Description:
 
DC motor is a rotating motor that can transform DC electric energy into mechanical power (DC motor) or mechanical energy into DC electric powered strength (DC generator). It is a motor that can convert DC and mechanical strength into one particular an additional. When it runs as a motor, it is a direct existing motor, which converts electrical power into mechanical vitality when it operates as a generator, it is a direct present generator, which converts mechanical vitality into electrical vitality.
 

Merchandise Title Z4-400-42 400KW 440V 500rpm Motor Z4 Series DC Motor
Motor Type DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor
(CZPT equipment)
Composition framework The composition of DC motor ought to consist of two elements: stator and rotor. The static element of DC motor is referred to as stator. The primary function of stator is to produce magnetic discipline, which is composed of foundation, principal magnetic pole, commutation pole, finish cap, bearing and brush device. Managing component is referred to as rotor, whose principal perform is to create electromagnetic torque and inductive electromotive force. It is the hub of power conversion of DC motor. So it is also commonly called armature, which consists of rotor, armature main, armature winding, commutator and enthusiast.
Model Z Type
Seat quantity Z315-Z1000
electricity sixty~2800kW
Voltage 220~1000V
Torque range 1.5 ~180kNm
Security level IP23, IP44
Cooling mode IC06,IC17,IC37,IC81W
Functioning speed  Constant Velocity /Low Speed /Alter Pace /Substantial Speed Other 
Principal classification DC Motor is a device that converts mechanical vitality into DC energy. It is primarily used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation electricity source of alternator. Despite the fact that in spots where DC electricity is essential, AC power rectifier is also employed to change AC into DC electricity, but from some elements of efficiency, AC rectifier power offer can not fully change DC generator.  
Software DC motors are widely employed in tape recorders, video recorders, video discs, electric shavers, hair dryers, electronic watches, toys and so on.
Maintenance approach Expert motor maintenance middle motor upkeep process: cleansing stator and rotor – replacing carbon brush or other areas – vacuum F stress dipping paint – drying – Calibration stability.
one. Use setting need to be always dry, motor surface area should be kept clean, air consumption should not be hindered by dust, fibers and other road blocks.
2. When the thermal safety of the motor continues to operate, it ought to be ascertained regardless of whether the fault arrives from the motor or the overload or the setting worth of the protecting gadget is as well lower. Soon after getting rid of the fault, it can be put into procedure.
3, make sure that the motor is well lubricated throughout operation. The common motor runs for about 5000 several hours, that is to say, lubricating grease should be included or replaced. When bearing overheating or lubricating deterioration is found in procedure, the hydraulic force should change lubricating grease in time. When replacing grease, the old grease must be taken off, and the oil groove of bearing and bearing go over should be washed with gasoline. Then ZL-3 lithium grease must be filled with one/2 (two poles) and 2/three (four poles, 6 poles and eight poles) of the cavity amongst the inner and outer rings of the bearing.
four. When the daily life of the bearing is above, the vibration and sounds of the motor will improve obviously. When the radial clearance of the bearing reaches the pursuing worth, the bearing ought to be replaced.
5, when removing the motor, it is Okay to remove the rotor from the shaft extension or the non extension finish. If it is not required to unload the admirer, it is much more practical to consider out the rotor from the non-axle extension end. When pulling out the rotor from the stator, the stator winding or insulation should be prevented from becoming destroyed.
six. When replacing the windings, the type, size, turns and gauges of the original windings must be recorded. When these knowledge are misplaced, they must be attained from the maker and the authentic designed windings should be transformed at will, which often deteriorates 1 or a number of performance of the motor or even tends to make it extremely hard to use them.

 

 

Z4-400-42 400kw 440V 500rpm Motor Z4 Series DC Motor

Tags: