2000e Electromagnetic Manual Sheet Metal Bending Machine

2000e Electromagnetic Manual Sheet Metal Bending Machine

2000E Electromagnetic Manual Sheet Metal Bending Machine 

Nominal ability 48″ (4-foot) length with a greatest potential of sixteen gauge moderate steel.
Eletrical Supply: 1 stage, 220/240 V ac and will perform at virtually any internet site.
Box Depth Endless
Bend Angle -180°
Transport dimensions  1.41m x .38m x .32m = .17m3 
GW/NW 153/150kg

a thousand electrabrake magnetic pan brake1000mm x 1.6mm Electromagnetic Sheet Metal Folding Device,No a lot more lifting!Solution image is only a representation, actual solution visual appeal could vary slightly  1
one thousand electrabrake magnetic pan brake 1250mm x one.6mm Electromagnetic Sheet Metallic

Folding Device Technical specs
Nominal capacity1000 mm x 1.six mm 39” (three-foot) size with a highest capability of 16 gauge delicate steel.Clamping force (with regular
entire-size clampbar)four.5Tons is consistent across the total beam, making it possible for for crisp bends even in the center of the brake.
CZPTmmended forHVAC shops,Tech faculties, industrial art shops, and general sheet steel fabrication stores.
Making enclosed boxes, triangles, alternate bends on various planes, and round products such as scrolling purposes.
Bending a variety of components, like sheets of moderate steel, stainless steel, aluminum, coated resources, heated plastics,and
more.Eletrical Provide:1Phase & Pneumatic air supply, 220/240 V ac and will operate at virtually any site.Nominal current:ten AmpDuty
cycle:30%Box DepthUnlimitedBend Angle0-180°Max. Clamping Bar LiftUnlimitedMax. Capacity with Extension18ga. (one.21mm) gentle steel /
21ga. (.83mm) stainless steelMax. Capacity CZPT Extension16ga. (one.51mm) delicate steel / 20ga. (.91mm) stainless steelThermal
Lower-Out158°F (70°C)Transport proportions 1.17m x .95m x1.1m = one.22m3 GW/NW150kg/130kgBlade gap adjustmentBlade gap adjustment on
the clamping bars lets you perform with sheet metallic of various thicknesses.adjustable back gaugesComes with item supports and
adjustable back again gauges for creation operates.Scaled stroke angle controllets you provide repeatable bends time after time.Notes
Capacities can modify relying on set up leaf extension. Rule of thumb for gentle metal, 16ga., extension OFF. 18ga. extension On
or Off, 20ga. and thinner, extension On.

Effortless operation
one.Put a piece of substance between the clamping bar to the depth essential.
two. Engage the potent magnet in the bending mattress with press button control.
3. Strike the foot pedal that softly clamps the content. This foot management keeps your fingers safely and securely out of the equipment to reposition the content.
4. Lift the the bottom bending leaf to total the bend and repositioned completely ready for another bend.

open-ended layout
one. makes it possible for you to develop fully enclosed ducts and designs unattainable to make with a traditional box and pan brake. 2. electromagnetic sheet metallic brake can bend containers or pans to virtually any depth,since it isn’t reliant on typical finger depths.CZPT components contain a storage tray, adjustable backstops, A total-size clamp-bar,and a complete  established of quick-duration clamp-bars.Optional add-ons CZPT for these models contain a slim clampbar, a slotted clampbar for forming shallow packing containers a lot more quicklySpecial tooling Special tooling can be speedily improvised from parts of metal to assist fold-up hard styles, and for generation perform the standard clampbars can be replaced by specialised toolingOperator SafetyOperator Basic safety is improved by a two-handed electrical interlock that assures a secure pre-clamping pressure is utilized ahead of full clamping takes place.
Complete-Length CLAMPBAR)Substance (generate/ult. pressure)THICKNESSLIP WIDTH (bare minimum)BEND RADIUS (typical)Gentle Metal
(250/320 MPa)one.6 mm30 mm*3.five mm1.two mm15 mm2.two mm1. mm10 mm1.5 mmAluminium
Grade 5005 H34
(a hundred and forty.160 MPa)1.6 mm30 mm*1.8 mm1.2 mm15 mm1.2 mm1. mm10 mm1. mmStainless Metal
Grades 304, 316
(210/600 MPa)1. mm30 mm*3.5 mm0.nine mm15 mm3. mm0.8 mm10 mm1.eight mmWith normal bending-beam extension fittedFor most non-ferrous
metals (copper, brass, zinc, and so on) refer to aluminium earlier mentioned.one-yr components guarantee as effectively as lifetime complex assistance by phone or

Applications of bening for metals

 

Add-ons Including 
 a storage tray, adjustable backstops, A complete-duration clamp-bar,and a full established of quick-duration clamp-bars.

Optional accessories
CZPT for these designs contain a slim clampbar, a slotted clampbar for forming shallow boxes far more speedily.

 

Packing:
Offering Models: Single product
Solitary bundle dimension: 1450X32X32 cm
Solitary gross bodyweight: 153.00 kg
Package deal Variety: Plywood box

 

Essential Data,
Optional add-ons NOT which includes in the purchase, if you require them, remember to get in touch with with me ahead of place the order.

 

 

 

2000e Electromagnetic Manual Sheet Metal Bending Machine

Tags: